ukbas.blogg.se - Technicolor router setup

#TECHNICOLOR ROUTER SETUP HOW TO#
#TECHNICOLOR ROUTER SETUP SOFTWARE#
#TECHNICOLOR ROUTER SETUP PASSWORD#
#TECHNICOLOR ROUTER SETUP MAC#

For a 4G Network Extender, the IP Address can also be found by pressing the display button until it is displayed on the screen.

#TECHNICOLOR ROUTER SETUP MAC#

The Network Extender's MAC ID is found on a sticker under the unit. This can be found by going into your router's DHCP settings and finding the IP Address that is assigned to the Network Extender's MAC ID# / Address. Note: You may need to know the IP Address assigned to Network Extender by your router in order to forward ports.

#TECHNICOLOR ROUTER SETUP HOW TO#

Visit D-Link's Tech Support page to learn how to create a port forward rule. Older model routers might require port forwarding. Make sure the following ports are enabled:.Please see the Specifications tab on D-Link's router product page for more information. Make sure your IPSec (VPN) passthrough is enabled and supported.Visit D-Link's Tech Support page for more information.

#TECHNICOLOR ROUTER SETUP SOFTWARE#

We recommend that you have the latest router firmware or software before starting the configuration process.

Make sure the following boxes have a check mark:.

If this username/password combination doesn't work, please check the stickers on the back or bottom of the router or contact your Internet Service Provider.

#TECHNICOLOR ROUTER SETUP PASSWORD#

For ARRIS models that start with TG or DG for username enter "admin" and for password type "password". How to configure your Time Warner Cable Arris Router to work with the Network Extender: Your 4G Network Extender is fully operational when the LED light is solid blue and it displays says "In Service" or "Verizon 4G LTE." Change security level to " Minimum Security (Low)".įor a 3G Network Extender: Wait at least 10 minutes after making the updates to verify that the SYS light on your Network Extender is no longer fast blinking red.įor a 4G Network Extender: Wait at least 10 minutes after making updates to verify that the LED light is solid blue.Select Firewall on the left menu under Gateway.If this username and password combination doesn't work, please inspect the stickers on the back or bottom of the router (that may show under "Network Key") or contact Time Warner Cable customer service at (800) 892-4357.For username enter "admin" and for password enter "password".

To access the admin portal of the router, open up an internet browser with a device connected to your router and enter.

How to configure your Time Warner Cable Technicolor Router to work with your Network Extender: Your Network Extender is fully operational when the LED light is solid blue and it displays "In Service" or "Verizon 4G LTE."

For a 4G Network Extender: Wait at least 10 minutes after making updates to verify that the LED light is solid blue.

Your 3G Network Extender is fully operational when all 4 LEDs are blue. The SYS light should go to slow blinking red, then the GPS LED will turn blue and finally the SYS will be blue as well.

For a 3G Network Extender: Wait at least 10 minutes after making the updates to verify that the SYS light on your Network Extender is no longer fast blinking red.

Enter the Network Extender's IP address from Step 4 above and select Save.

Navigate to Advanced, then DMZ menu to enable the DMZ for the Network Extender.

If the Network Extender does not show in the next 30 minutes, then call Comcast for Technical Support (800) 934-6489. Note: If the IP Address does not appear within 30 minutes, reboot the Network Extender. For 4G Network Extender, the IP Address can also be found by pressing the display button until it is displayed on the screen.

When the device name appears, record the IP address for the next step.

Wait for the Network Extender to show in the menu as Connected via Ethernet, which will show both IP and MAC addresses.

Go to Connected Devices and select Computers.

In the setting for IPv4 change the Gateway Address from 10.0.0.1 to 192.168.0.1.

If you need additional assistance, visit Find and Change Your Wireless Gateway Network Name (SSID) and Password (Network Key) page. For username type "admin" and for password type "password".

Access the admin portal of the router with a device connected to your router, open an internet browser and enter:.

See the instructions below for how to configure your Comcast Cable Router to work with your Network Extender: